Recent content by 68HemiRR

This is the Speedometer Cable Retaining Clamp And Bolt that holds the aluminum adapter that mounts the speedometer cable in the tail shaft housing. Fits all 1966-76 A, B, C, E, F bodies. Use with automatic 727, 904, and 833 manual transmissions. Use with 26-45 tooth pinions. $15.00 shipped to...

This is a Set Of Four OEM Plymouth 14" Wheel Covers. #2823010 This set came off a 1967 Plymouth GTX, but they were used on several different Plymouth models in the 1960's They are in very good condition. $80.00. Local pickup or buyer pays shipping.

This is a 340 Cam Thrust Plate Oil Drip Tray. It is original, not a china knockoff, and is in good condition. Just could use a cleanup. It should work on most Mopar small blocks. $20.00. Local pickup, or buyer pays shipping.

This is a OEM 340 Fuel Pump Eccentric W/Bolt & Washer. It is original, not a china knockoff, and is in good condition. Just needs a cleanup. It will work on most small block Mopar engines. $25.00. Local pickup, or buyer pays shipping.

This is a OEM Mopar 11 3/4" Flex Plate W/Bolts. It came out of a 1967 GTX with a 440hp engine, but will work in any big block with the 11 3/4" torque converter. It is original, not a china knockoff, and is in good condition. Just needs a cleanup. The 10 original bolts are also included...

Does anyone have a use for some left over Holley Manual Choke Parts? I bought the 45-223 kit 20+ years ago to convert to an electric choke. These are the parts left after the conversion. $20.00. Local pickup or buyer pays shipping. (I also have a 42" choke cable if needed)

This is an OEM Big Block Mopar A/C Water Pump Pulley. It came off of a 440 with A/C. It is in good condition, just needs a cleanup. The dimensions are 5 7/8" x 1 1/4". $20.00. Local pickup, or buyer pays shipping.

This is a OEM 1970 to 74 Blower Motor Vent Tube. It is original, not a china knockoff. It came off of a 1970 Challenger SE big block with A/C. It is listed as the correct part for 1970 to 74 B&E Bodies, but may also work on other models It is in very good condition, and the rubber is still...

This is a OEM 1967 to 72 Big Block A/C Idler Pulley. It is original, not a china knockoff, and is in good condition, but could use a cleanup. The pulley is nice and snug, spins freely, and does not wobble. $25.00. Local pickup, or buyer pays shipping.

This is a OEM 1966 to 73 727 Trans Throttle Pressure Lever with bolt, nut, and washer. It is original, not a china knockoff. It is in good condition, just needs a cleanup. $20.00. Local pickup, or buyer pays shipping.

This is a Used OEM Aluminum Thermostat Housing #2780970. It is in good used condition, but could use a cleanup. $25.00. Local pickup, or buyer pays shipping.

This is a Complete set of 34 OEM Big Block Cylinder Head Bolts, and 8 intake bolts. They are original, not china knockoffs, and are in very good used condition. Just need a cleanup. I know there are people out there who say you must buy new ARP when rebuilding an engine. All I can tell you is...

This is a Lot Of 9 Assorted High Performance Mopar Magazines. They are in very good condition. I had many more of them, but I had them stored in cardboard boxes in the lower level of my home and several years ago during heavy rains we got water downstairs, and many were damaged. These are...

This is a Big Block Mopar Coil Relocation Bracket. It is in good condition. $25.00. Local pickup, or buyer pays shipping.

This is a 1968 to 1970 Upper Shoulder Belt Holder. It is stamped 8L which I believe would be the left side. It is in decent condition, but could use a cleanup. It's off of a B-Body, but may also be correct for other years and models. $20.00. Local pickup, or buyer pays shipping. (I have not...