Search results for query: *

My mistake. I missed that it is a four door hardtop. Side windows are different, but so is the backlite between sedan and hardtop. Here's the revised answer that I should have made earlier: For the 1973 Dodge Polara four door hardtop, the following backlite (rear window/glass) applications...

For the 1973 Dodge Polara four door sedan, the following backlite (rear window/glass) applications will interchange: - 1969 - 1973 Dodge Polara four door sedan - 1969 - 1973 Dodge Monaco four door sedan - 1969 - 1973 Plymouth Fury four door sedan Hollander interchange number is 3440. Edit...

The reproduction clips listed at the following, aimed at B-bodies, might be of use: Air Conditioning Line Clamp Set Mopar

Unknown if this is a direct cross to the BPE 6044, but RockAuto has this single action valve for some Chrysler applications, plus others, on closeout for $5.66: T38608 The valve is listed with unspecified "Famous Brand", but is likely CarQuest. The Four Seasons and Murray number 38608 fits...

The fuses are listed on page 61 of your owner's manual: Following is another listing of the fuses from the 1973 Dodge factory service manual: For more information, including wiring diagrams, online copies of the factory service manual are available from MyMopar.com at the following: 1973...

The temperature operated vacuum by-pass valve, or more formally Thermostatic Ignition Control (TIC) valve, as the service manual page explains is used to reduce the possibility of engine overheating. It operates by switching from carburetor ported vacuum to full manifold vacuum if coolant...

Painting my wheels (#3766077):

Fin straightener by Robinair.

Unicorn 2500 Impact Driver. I've had it since the late 1970s or early 1980s, but it was used when I got it. It is ideal in some situations where it's too tight for hand tools, but an air impact, or other means might risk rounding out/off, such as the #3 Philips head screws holding the door latch...

Chrysler started using the Nippondenso, aka Denso, starter in 1988. These starters were revised multiple times since introduction. Only the first few years of production are suitable for bolt-on use on earlier engines. Bolting onto small blocks is typically relatively issue free, but some...

I don't use it much. I bought it sometime in the 1980s.

Inspecting, cleaning, and lubricating a transaxle to replace the unit that locked up in my 2001 MTD Yard Machines riding lawn mower. This one is actually a little older than my mower. The differentials are not limited slip. I haven't removed the locked unit yet to disassemble and see what locked...

Blocking off guide coat. 96 degrees F ambient, but 105 degrees F at the car due to the concrete and metal around. At least it dries fast.

The original Air Valve Tool was Carter 109P-397 or Miller Special Tools # C-4152B. Miller is now OTC. These are not available new any longer, but might be found used or NOS. The last source that I knew of was DynoRoom Tools, but you discovered that it is no longer available as well. Bill...

The part is the air pump, or aspirator, crossover pipe. It connects to the back of both exhaust manifolds as shown in John's image, or as in the following image, which is for a 1977, and the same as 1978. The pipe fitting/flange is secured to the manifold with a stainless steel bolt with a...

The pictured engine block with casting number 3614230 is a 400 and with a casting date of 9/16/71 is probably a 1972 400. As mentioned, the pad next to the distributor will yield more information, but should have "H400" stamped for 1972 with other numbers. Block casting 3614230 was also used in...

The leakage could be the threads into the pump body, but as a first try, loosen the clamp and raise it up on the hose a little. The clamp should be on the smooth area between the fitting's threads, and its raised lip on the end. If clamping on the fitting threads, it may not seal. It looks like...

The ammeter itself contains the shunt, which is a wound coil of relatively fine wire. The feed wiring which is tapped off the cable from the alternator is typically 20 AWG wire. As shown in the service highlight, with a 40 amp example, the current divides between the large alternator cable and...