Search results for query: wiring harness

Perhaps someone did some rewiring. Before pulling everything apart: I would Check continuity from connector at the auto trans 3-prong switch to the fusebox to determine whether you have continuity to power. Then check continuity from the backup light sockets to the other outside terminal of...

...a tighter spec than the modern ones, OR get breakers for the key circuits to fit too. Mind you, electrical wiring is one of my major specialties and talents, and I realize not every soul is so gifted, but if you love your Mopar, DON'T WASTE YOUR KRONER ON BRAINLESS WIRING HARNESSES! Best...

My worst nightmare hahaha

Evans Wiring Harnesses should have the under-hood harness and maybe some more. What I've done with other cars is lay the existing wiring out on a piece of plywood and laid out the "pattern" with headless finishing nails. Then unwrap and change one wire at a time and rewrap it with harness...

Long-time no speak for myself here on the forums. Despite multiple attempts to sell the car for money I just can't seem to get an acceptable offer! Did have one amazing offer from a fellow member here for a trade, but in the end I feel like it comes down to me needing to finish the car if I...

...wiring and terminals. At the time, nobody else was doing that. In those earlier times, even with the '55-'57 Chevy vehicles, some wiring harness suppliers sold harnesses with the correct color codes, BUT had thinner and shinier insulation on the copper wires. Theoretically correct, but not...

There is no relay.

When you use this method, which seems very good, do u still utilize the firewall milti pin connectors?

That is a good approach, especially with more complex wring, or running and terminating new wires. I've used similar to some scale in the past for things of mine. In my pasted case, I had the old harness to go by for where to make branches for some wires, and the car sitting right behind me for...

Maybe invest in proper battery cables as well

Thanks for the replies guys. I did see those videos and the very helpful diagrams, at the moment everything is stock save for a headlight relay harness so until I can get my hands on some 8 gauge wiring, I'll just move the headlight relay feed wire to the alternator. I've cleaned up the bulkhead...

Oh sorry, I was actually asking about the bulkhead bypass wiring just from the alternator to the ammeter. Was wondering with the stock setup, if I can get away with just 10 gauge wiring. It's a 67 Fury, the lamps are 2x 55/60W and 2x 55W H4 and H1 bulbs respectively. The headlight relay harness...

...The voltage regulator pigtail, part number 2983727, was available from Chrysler but now discontinued. A good used one from a scrap wiring harness can be used or new aftermarket is available. Standard Motor Products S-573 is commonly available. A metal retainer, part number 3588348, was also...

I have tried to reach QQE through this forum with no success...his last action was 2023 here. Can anybody help , I would need 8 pc of these black correct ones.

My turn signal switch broke again,find out it does not like when i hand force it to cancell example switching lines and only need few blink. Found this page: https://www.corvairkid.com/67-9signal.htm When i checked my steering column components turned out the different hole location is there...

I have the older style (cannister type) VR on my 69 Fury. My replacement engine wiring harness when car was restored 8-10 years ago was set-up for that style VR. I'm running the round back / single field wire alternator and mopar electronic ignition. I had a solid state VR unit in it that...

Also on the diagnostic machine I started checking pin connections from the engine harness back to the analyzer. I found when I stuck my amp meter probe in, one of the plug sockets would back out. I also found that one of the other sockets had a loose wire. Waiting for some new sockets and plug...

Unfortunately for me, the cigar lighter wire is crimped directly to the fuse holder terminal in the fuse box. Fortunately, it was easy enough to add a relay in, and have it activate when the key is turned to accessory mode. Stock cigar lighter socket, with a pink and red wire going into it. A...

There are also these. 5/8" size. Dash Tail Park Lens Lamp Light Bulb 5/8 Socket Wiring Harness Fits Chrysler C | eBay

Do you need a part number from Hamtramck to understand it? You seem to get it but for those that don't understand, please don't waste your time trying to help a fool.