Search results for query: *

Yes start them in the center and point outward

Yes must go and look it over. Nice it's a 440. Good looking car and in decent shape. Could clean that one up. Needs a different whee/tire look

Your car had a ER6 red body, V1W full white vinyl top. The EW1 is white upper door frame paint. The "hurst" white hood treatment and upper body paint has been added. It just follows body lines so it's an easy thing to do. Looks good on there and goes well with white interior.

What year is the engine? Does it have stock pistons? Definitely raise the idle speed. Don't block the heat crossover, it will cause you many problems with driveability.p, stumble bog. Watch this video below about the heat crossover, why a carbureted car needs it open and working and why a...

Well there is your answer. Do that modification and new pump before you leave town. Modify 2 pumps and keep the spare in the trunk! I have bought from hot heads, a good place to have around for these cars.

Good to think of this now. If no answer here try the forward look page. Many folks over there smart on the 50's cars. Might be an off the shelf solution. Home of The Forward Look

Plates can be saved if the guy had the proper tools to grab the bearing ony and would not destroy the plates. Look at your plates and adjuster make sure they are flat and in good shape right now. Not rusted up.

I've been around for years and know how to do it. It's not working on FCBO for me. All the pop ups are covering up the messages I want to delete. When I first open the "show all messages" there are no pop ups so I click on the title to open it but nothing happens. The the pop ups arrive. I can...

I'll take these. Your pm box is full

Inner axle seals at rock auto. Yes pack the rear bearings in grease. Since the gear oil washed the grease out they need repacked now.

Then it quick to torch or sawzall off the sump and pickup.

A small block pan is just as easy to take off as a BB The not fun part is removing the center link. Could unbolt it and then lift the edge up to remove pickup. And a SB just 2 oil pump bolts takes off the pickup also. No need twisting it and needing clearance for the twist on a BB

Yes sounds good. you can leave the trans on the jack under the car, and you can check the u-joints while the driveshaft is out. It's just hard to feel when something is bound up when trying to clear the crossmember with the oil pan and tilting the engine.

Hold on folks. Let's discuss this 2 inches idea. Yes the converter goes in the front pump 2 inches. But the input shaft goes inside the torque converter about 4 more inches. So is this 6" total. The end of the input shaft is about 1/2" from the front edge of the bellhousing. And the oil...

Anyone know what happened to this car? The photos color look off. I thought they were black and white at first. On the seals looking gray, maybe they tinted the photos gray to make the paint look better or to hide flaws? Maybe it's the lighting in the building and what the camera picks up...

I think it is not that rare when new. But over the decades of people robbing the 440 magnums out of them they are rare now. I've owned L code (375 HP) and K codes (350 HP) and the power difference is noticeable. But K code engine in good condition runs very well and powerful. Still have...

1965 only

If it cranks the fuse I left link is good. Need to check for spark. All these new parts could mean problems. Pull coil wire from cap and place it near metal and crank it. If it sparks and won't start pull a couple easy plugs and make sure they are not wet or fouled. Yes make sure battery is...

Ok so this one in first post is a 66 Fury. A 67 has the base that's almost flat. They are solid mounted for sure.

Very true, but a glass guy of today doesn't have to deal with metal trim around the glass. It's all held together with urethane. Cut it out and toss it, install everything new. Try asking a current glass guy about doing glass in gaskets like our 60's mopars, most won't even consider it...