Search results for query: *

I purchased rear drums and shoes for my 1967 Plymouth Fury from Craig @mobileparts at Carlisle. Apparently the correct NOS 11" x 2" drums are hard to find. Craig only has 1 left. We decided to experiment with the fitment of C2955 for a 1969-1972 on my 1967 with 14" wheels. C2955 has fins on the...

quick electrical fire (just a puff of smoke and immediately pulled over). Afraid to drive it now. This was a test run for Carlisle. Pretty aggravated.

Does anyone have good pictures of their control arm splash shields installed? Ive found some pictures in here, but usually only one piece of the shield. Does anyone have a picture of the whole shield, left and right. Mine were shredded when I took them off. Thanks. Trying to finish off some...

I recently had everything out of the engine bay, so prior to reinstalling the Master Cylinder I bench bled it with full piston travel, dumping the fluid back into the reservoirs. Now I just tried to bleed the brakes on the car. The rears seem fine. When I got to the fronts, I topped off the...

It's been way too long since I took these seats apart and apparently I didn't take good enough pictures of the disassembly. Where does the back tang of the trim go? I'm assuming it screws to the frame, but I can't picture it. Also, where do the hard plastic spacers go? Do they go between the...

I think I might be going crazy, but can someone help me understand the headlights. It was my belief that H5006 (3-prongs) was the low beam (meaning the headlight on the bottom) and H5001 (2-prongs) was the high beam (meaning the highlight on the top). In my situation, the notches on the back...

Are there supposed to be 1 or 2 piston retainers? Also, how is the rubber boot supposed to be properly installed? If anyone has any pictures as an example that’s be great. Thanks!

Since I tend to take more things apart then I put back together, today I planned to take my reservoir off and replace the big main O-ring/seal. I also wanted to get a better look at the filler neck because I believe my reservoir leaks where the filler neck comes together with the reservoir body...

Car: 1967 Plymouth Fury III I tried installing two 3.5 inch speakers into the single front 4x10 location and it’s not going to work. I ordered a mount that is shaped like a 4x10 but holds two 3.5” speakers. https://www.classiccarstereos.com/hertz-dieci-dual-dash-mount-speakers-90-watts.html...

I have my steering column out, so I'm going to re-pack the lower coupling and I was thinking about prepping removing and painting the floor plate so it won't be rusty anymore. I was also thinking that I might as well replace the lower steering column bearing. I've been reading on pages 19-34-37...

I came across this Michael Ray song Holy Water. Check out the music video. Is that a '67 Newport? I find it funny the lyrics say "He bought a brand new Lincoln."

I am hoping to buy the dash pad @67-Fury has listed. His is blue, but I will need to paint it red. I was on the phone with Chas from 8774Paint1 trying to figure out a solution. He couldn't find any paint codes for a '67 Fury interior. For a '68 Fury he could find Aztec Maroon Poly Low Gloss...

Does anyone have a picture of how their transmission cooler lines are run on a small block with a 727. Preferably a 1967 Plymouth fury III

For Sale: Rear seat covers for a 1967 Plymouth Fury Convertible. Purchased from Legendary. I accidentally bought the convertible seats when I needed a hard top. Legendary won’t exchange them for me because it’s been too long. 67 SPRT FURY/FURY III CONV UPH MET RED W/ METALLIC RED ACCENT $350...

How would I know if my car came with the 02 Red or the 13 Maroon? Does that numeric code align with a build sheet or tag found in the car anywhere, or is that just the code ACC uses? I'm pretty sure mine is red but I don't want to screw it up.

I figured I'll play the game. Found a picture of my tag from before I cleaned the engine bay! 1967 Plymouth Fury III

My wife got me an ad for a 1967 Plymouth Fury III 4-door for Christmas. She was trying to find a red 2-door like mine, but she said this was the closest she saw. She said she liked the couple in their dress clothes. It has currently found a home on an old TV stand I converted to our bar. I...

For everyone’s knowledge. Remove post if this has already been noted. Article is from 25 Jan 21. Mo-Par City Is Closing Its Doors After 50 Years

I am attempting to wire 3 Autometer gauges. I have been told the following: To power the gauges, you want to find the Ignition (RUN) circuit. Which means that circuit always has +12V on it when the engine is running. You don't want to use the Ignition (RUN/ACC'Y) circuit because the gauges...

Someone educate me on carbs please. I am installing a dual feed fuel line on a Holley Street Avenger. When I removed the original fuel inlet adapters a copper type piece and a spring fell out. (See below) The fitting shown above is slightly recessed and allows the copper piece to sit...