Search results for query: *

Does anyone have a picture of the topcat brand door panel side, window fuzzies? I have a set of pui and they are not like the original ones at all. They have a flap that I guess the window is supposed to hold up, but even with it pushed up tight, it doesn't reach the chrome piece at the top. The...

Thinking about putting Edelbrock Performer RPM on B engine in my 66 300. Will I have hood clearance issues?

I recently had my power steering gearbox rebuilt. During reassembly of all new steering components, it appears that the gear box may have been assembled with the shaft going to the pitman arm a tooth or 2 off if that is possible. With the master spline on the shaft that goes to the column at 12...

Need a little guidance. I am putting front suspension back together and I am not sure what the orientation of the torsion bar adjuster should be for installing the torsion bars. The nut holding the lower control arm in is loose, suspension is hanging as low as it will without pulling down on it...

Does anyone here have any experience with strut rod bushings with no sleeves? I am restoring a 1966 300 and the strut rod bushings I got from Mobile Parts didn't come with sleeves. The directions refer to both with or without sleeves, but 3 of the rubbers are very sloppy on the bar and one is...

Anyone know where I can get a couple of these? The round bar is just under 1/2".

I'm struggling with the installation of new upper ball joints on my 66 Chrysler 300. I had a hard time getting them threaded in and when I finally did they got real loose in the hole just before they bottomed out. Real loose, you could wiggle it in the hole. When you keep turning it , it...

Having trouble understanding the fender tag on my 66 300. When I decoded, it indicates both bucket seats and bench seat. It also says it has a console. The car has buckets and console. The reason I am checking is because I removed the steering column and ti is scratched in a few places and looks...

I am disassembling my 300 for restoration and I am in the process of removing various mouldings and was looking for any tips from all the experience here. Top moulding that goes full length of car. Is there any way to get the moulding off of the clips without ruining the clips. I understand...

Is it normal for new shocks to have peeling paint on lower rubber bushings. For some reason I can't upload a photo. It says the file is too large. Never had the problem before.

Looking for recommendations on what shocks I should put on front and rear of my 66 300. Not towing anything.

I'm thinking about building a stroker for my 66 300. Other than the 383 that is currently in the car, I have another 383 block and a 400 block. I was thinking about a 451 or a 512. I was hoping to get some opinions, I know there will be a lot. What I am hoping for is something that is very...

Other than trim, are 65 and 66 Chrysler fender skirts the same? Interchangeable ?

Had them all out today so I thought I would share a few photos. The slabs had the majority so I am posting here. Just got the 66, so there are some changes coming there.

I am thinking about putting P275/60/15's with 8" magnum 500's on my 66 300. That is what is on the back of my 67 Newport, so I am assuming they will fit. Is anyone else running this size on the back of a 65 or 66?

Is the light bulb socket on 66 300 tail light a friction fit into the housing? Or do you have to twist them to get them out? Don't want to break anything. Thanks

Just took her out of the trailer. Not perfect but good enough. Going to have to change a few things like exhaust, and it needs front seat covers. I think it wants magnum 500's on a little bigger tires as well. Lots of things to change under the hood.

Having trouble finding a good site to decode fender tag on 66 300. Can anyone either share a link or help decipher this tag? Thanks.

Today a friend of mine blew a core plug on his 1962 361. Apparently they are a different style than the cup type. The local wrecking yard that has a lot of old parts thinks he may have some but I need the diameter. Does anyone know in the diameter would be the same as any big block cup style...

Does anyone know the difference between 2464324-AD and 2464324-AC? I have the AD version. It is plastic and the raised rubber sealing surfaced does not get completely covered by the pan in the middle at the back and at the right rear corner.