Search results for query: *

Ok, I pulled both axles of our 67 New Yorker. For inspection and freshening up. Good thing I did, oil seals need to be replaced. Pulling the right side axle however, a small part came along and fell to the floor when the axle came out. I fear it is something which belongs in the differential...

Ok, I'm doing the rear brakes for the first time. My question is about the bottom spring. The lower springs on my car are attached to the "adjusting lever" (see pictures). Is that ok? It seems like it worked fine. The service manual and online videos however, seem to show this spring attached to...

Ok, I'm replacing the rear brake shoes and hardware. While at it, pulled out the driver side axle out to inspect the bearing. Cleaned it and it looks good. Will put fresh grease in it and also replace the axle seal. After the driver side is back together, start the passenger side. Before I...

Asking for an acquaintance, is it possible to see if the engine belongs to the car? It's a 413 in a 1964 Chrysler NY wagon. Number says V 41, 1018

Guys, asking for a friend, he´s looking for weatherstrips for his 1964 Chrysler New Yorker Wagon. Specifically the ones for large side windows at the end of the car. Left and right side. Can these still be bought somewhere?

Ok Guys, the windowregulator spring came off. And now I have no clue how to put it back on the regulator. Got it in once with force, but it flew off as soon as I turned the crank. Scary stuff ;-) I fugure it must be under tension when the glass is rolled down?

For those hard to find C bodie plastic parts, 3D might be the solution. Take the originals to a 3D shop and have them copy them.

Ok this is in the Netherlands (Europe). A giant shed with NOS and used parts nearby. The owner died, and now they are trying to sell as much as they can. Or the (precious) parts will go to the shredder.. An acquaintance bought alot of stuff and told me he also bought a grill, which looks like...

Hello guys, like the title says, how to remove the wheatherstrip on the door? I'm in the progress of pulling out the left door glass including front track. That seems impossible with the wheatherstrip still in place. The manual says to remove it. But how? I'm doing this because the (manual)...

Finally we get to put some miles on our New Yorker. The smooth ride was a pleasant suprise.

Ok, 1967 Chrysler New Yorker 2 door, driver side window. It worked fine 2 weeks ago. Now window is up, but won´t move anymore. At first I suspected the switch. But when bypassed, 12 volt directly from battery to windowmotor connector (the grey one in first picture), nothing at all.. Switched...

Hey guys, Today we bought this very nice 1967 New Yorker. It will be in good company of a 69 300, and 69 Fury. It´s in the Netherlands (Europe). 440/727, runs on gasoline and LPG (just installed by previous owner). Question, what are those little gadgets for on the front bumper? Sensors for...

So, yesterday a nice 1967 New Yorker caught my eye. Numbers matching with buildsheet, fendertag. As a fuselage owner I know nothing about 67´s. And would like to know a bit more about these cars. Are these models rare, desired? How many where built? Is drivebility the same or worse then 69's...

Hello, I finally found a RH side side mirror for my 1969 300. But unfortunatly without the gasket and 2 nuts. So, looking for the gasket and nuts. Pictures are examples. Thanks.

Just curious, how to check if the transmission is numbers matching? If possible at all. See attached photo of the transmission nr on our 1969 Chrysler 300. The number 2648 stands for 1968 according to the 10.000 day calender?

Guys, car functions fine, runs and starts good. Except for a small problem when running on LPG. I won’t bother you with that. But because of that problem, I measured power at the ignitionswitch. And I wonder if the voltages it shows are normal. The red wire shows a nice 12,36volts. With the key...

Probably silly question, but were 69 Chrysler steering wheels perfectly round? The used wheel I got is wider than it is high…? Before I start restoring it..

Hello Guys, I bought used "Three Hundred" letters (1969) from a fellow member on this board. Now to mount them, I would like to know the exact measurements where to place. Is there any information about this matter? It's not in the service manual..