Search results for query: *

Yes, I agree. I don’t know of a way to reattach wires to back of mirror. On mine it’s the up/down cable that has come off mirror. It’s a shame because my mirror housing is mint. Got to figure out how to get it apart at other end/slip it through/remove from housing/get another good mirror and...

My chrome mirror surround is mint except up/down adjustment flips around due to control wire broken at mirror end. I do believe mirror could be changed out but I’ve never done it. If so, perhaps some guidance would help me along with a good replacement mirror/remote adjustment mechanism. If...

According to the 69 Polara photos (thank you very much MrMoparCHP) that looks to be the correct air cleaner that The Goose posted…thank you. Think about what you want for it. I see where you are. I guess we couldn’t get much farther apart. You being on west coast and me being close to the east...

I bought a 69 Dodge Polara with 318 several months ago. A previous owner put chrome valve covers on it...round chrome air cleaner too. I like original, so...I'm now looking for original valve covers and air cleaner. If you can help please reply and I'll PM you. Some photos would even help me if...

Here’s a photo of a few clips that fell out from right fender. Basically, the front and rear nutted clips are holding it on right now. I suppose I can carefully grind down rivets/drill holes/use generic nutted clips but I didn’t want to do that unless I have to. Here’s a photo of the original...

No rubber bumper in molding...just anodized aluminum...thin moldings. I take they’re not reproduced...must be Polara only (not on any b-body cars)...Can’t find them anywhere.

Just wondering if anyone has any tucked away or knows where to get these little white clips that fit on the rivets on body and hold on the thin (~1/2”) trim that runs from front to back on the body line. Thanks...

Thanks everyone for your PM's, e-mails and photos. I'm putting this on hold for the time being as another member is doing the switch from a Carter BBD to a Stromberg WWC. I'm waiting to see his results before I make a decision on what to put on my 383. Bob

Thanks...I don't see the third screw in the back like mine has. I see an extra vac. nipple back there that's plugged. The throttle linkage setup looks quite different though...no long horizontal post for the trans kickdown. I'm not sure if this an issue but the cover is different too...taller...

From all the information I'm gathering...now I'm thinking I need a Carter 2 Barrel that's somewhat different than the one on my car right now...because it sounds like it's problematic. I should find one that has the lower two adjustment screws in the base at front...AND WITHOUT the single...

Please PM me if you have a 2 barrel Carter carburetor off of a 67, 68, 69 vintage Mopar that perhaps you have removed to upgrade to a 4 barrel setup. Would be great if it was working reasonably well before you removed it. But...even if it was not, perhaps it has the proper base I'm looking for...

Looking for decent used set of four 15" Magnum 500's to put on my 68 Fury. These should be the chrome wheels...not the silver/black painted wheels with trim rings (which I think only came in 14" but not sure) Please PM if you have a set and are thinking of getting rid of them. I'm in the the...

I've been looking for a set of used/working fender turn signals for a 67 or 68 Dodge Monaco or Monaco 500. Not sure if Polara or Polara 500 would work as most of them (I suspect) had the belt molding trim that ran from front to back which incorporated the turn signals. I'm looking for "the stand...

Looking for a good used set of fender (top) turn signal indicators for my 1968 Dodge Monaco 500. My car does not have the belt line molding (on top) from front to back so I need the "stand alone" fender turn signals. These were found on Monaco, Polara 500 and Monaco 500 for 1967 and 1968 model...

Looking for a nice driver or 3+ condition 1967 or 1969 Dodge Polara/Monaco/500 2 door hardtop. 383 2v preferred with no A/C but will consider a dealer installed A/C car as it's all easily removed. Not looking for a project car. Thank you! Bob trustinchrist@rochester.rr.com