Search results for query: *

Having some EFI trouble, tech support non existent. Anyone has some knowledge on EFI system? Pretty much the system gets stuck in open loop randomly, thats how it started. The o2 showed normal values but the fuel trim just...stopped. Reflashed the software a few times and every time I do it...

Hello, Had just installed some headers and the drivers side is fine and makes almost 0 noise. The passenger however has a real loud tick. The ball connector seems fine and I cant find any carbon tracing. Does this sound like its the manifold gasket? I used the cheap ones that came with the...

Hey, I need some guidance on what could cause my 360 to shake pretty decent at idle. Its the same in gear or park and sort of new ish. The engine always had a little shake but not like that. Two things, I am running efi and have tried to adjust the idle to the most stable solid vacuum and such...

Hey all, I am running an efi on my 360. Replaced the plugs yesterday and for some reason cylinder 8 was wet. The plug looked a little darker than the others but not substentially different enough and I run a CDI ignition. I'm thinking it might have been oil from a valve cover leak but I have...

My Fury has started with a decent rattle sound at idle that has been getting a little more consistent today after some WOT tests from stop in a parkinglot.. I have had some starter kickbacks after installing a multispark and it now makes the same rattle sound when cranking. Happens more in N and...

Has anyone here done a fuel hardline with AN compression fittings? I am looking to do a hardline from throttlebody that curves down by the waterpump and there ill attach a soft hose. What material holds to 60psi and woul compression fitting hold that pressure too?

Whats the general rule when you rev the engine and it pops out the carb and/or stalls? I recently installed an open spacer and now when i rev the engine a little while its its under 100°, i get this backfire cough through the throttlebody. I could actually make it stall once or twice. I have a...

Last year I installed some fabricated valve covers on my Smallblock along with..i think they were edelbrock gaskets, they have only a couple hundered miles on them. I don't know if i haven't tightened them enough or what but they leak!!! It looks like the oil is seeping through the gasket, both...

i got a leak at the area where the dipstick tube goes into the trans, is there a seal for it or anything that i can replace or do i have to pull it out and just smear rtv on it? Also, when i get the tube out, will the trans fluid leak out?

...you cant get the pipeplug out of the 8 3/4 because it is inthere so tight almost like its welded together? I put a wrench on it, didnt budge, sprayed it with wd40, have it some slight whacks with hammer, put wrench back on. Nothing. Whacking the wrench with a hammer doesn't make it move...

Just ordered an EFI set :thumbsup:. Decided that if anything is available under $1300, ill do the swap. Have heared nothing but good about them even tho they are pretty new on the market. Only 5 wires to connect and can use the low pressure pump I already have. Its got 3 weeks backorder, but i...

I have had this happening pretty much since I got the car and just noticed it again. When the weather is warmer and I park the car, I get a puddle of gas under it which is coming from the gast tank vent. This almost only happens when the tank is full. I am wondering if thats normal or if there...

Hi all, I am trying to help a neighbor with her car (non mopar lol). Shes got an issue with the carb, she got starnded because she was out of gas, we put some gas in and started the thing up. Engine was cold. It ran for a couple minutes and then started to act up like a cylinder wasnt firing...

So, i have a new starter installed because i had an issue that when the car is hot and sits for a while to heatsoak, the starter wouldnt turn the engine. It would just....turn a little and then stop but not disengage. Installed a new mini starter, everything fine for a while, cold crank, hot...

Hi, ...im going through the fury right now to check for some maintenance items i have to replace before I loose the garage... This time: motor mounts. My fury came with a 318 but the PO installed a 360. I have always noticed how the engine shakes a lot at idle, im also still have that weird...

Hi all, I have a Holley Mighty Mite electric fuel pump. I just tried to figure out where to implement it in the system back by the tank... the instructions say "no more than 12 inch from fuel tank vertically (bottom)" would one interpret that as "not more than 12" above the tank?" The pump is...

hi all! I need someone who knows holleys. I have a 670cfm street avenger which... idles 100 times better than my carter and runs pretty good down the street. I just have this off idle lean spot when I push the throttle a little harder. Idles at about 13.5 to 14:1 afr and when i hit the throttle...

I have no experience with AN Thread sizes and need help figuring out the Size of this AN Thread so i can order the correct fitting for my fuel line. I dont have the Carb/Fuel line here to measure it and want to be prepared for the Install :) seller says "it has a 3/8 nut on it to accept a...

Hi, after debating if I should simply buy a new better Carb, I came to the conclusion that this is worth a try before shelling out $600 for a fully tuneable carb and I thought I share this here. First, I put a Wire in my Idle Air bleeds and found out, that this gave my Idle Screwes a lot more...

I have been doing a lot of reading up on Carbs lately and i came across two possible candidates for my mild 360. First is a Street Demon 625cfm with the tripple stack boosters, Second is a Quickfuel SS 650cfm with Annuel Boosters I'm so fed up with my Carter AFB and it's little quirks all the...