Search results for query: *

Here is a pair of big block engine mounts in very nice condition with as new isolators too, bolts are there as well, I would like $75 plus shipping for them.

This carb has been in storage for a number of years, butterflies still operate fine. I won't be using it so time to sell, I am asking $100 plus shipping for it.

Here is a nice Carter carb that I have had ibn storage for about 5 years now, its time for it to go to someone else, I would like $100 for it plus shipping.

Here is pair of valve covers in nice shape, one has a little rust on the inside of it but wont be hard to clean that out. I would like $75 plus shipping for them.

This air cleaner came off a 400cid engine but I cannot say exactly what year it is, the carb was a thermoquad but this air cleaner will also fit an AVS carter or similar. I would like $50 plus shipping for it.

Here is a B body HP manifold that appears to have the part number 2806974, it is in good condition, shows no cracks or breaks and no chunks missing. It came out of a 1970 Plymouth Sport Fury car so it will fit cbodies too. I would like $100 plus shipping for it, thanks. So far other quotes for...

Here is a freshly painted dual snorkel air cleaner in very good condition, I would like $175 plus shipping for it.

Here are a pair of valve covers though a bit dusty are in good condition, they have been sitting on my shelf for a couple of years now and I think it is time to move them on, I would like $150 plus shipping for them, thank you.

Here is a B body HP manifold that appears to have the part number 2806974, it is in good condition, shows no cracks or breaks and no chunks missing. It came out of a 1970 Plymouth Sport Fury car so it will fit cbodies too. I would like $100 plus shipping for it, thanks. So far other quotes for...

Hey all, here is an aluminum inlet manifold in very good condition, there is no corrosion , cracks or warpage at all. I checked the mating surfaces with a straight line rule and they are perfect. I would like $100 plus shipping for it, thanks.

This has been repainted and looks very nice, it does have a scuff mark on top of the tip of the snorkel itself which will need a touchup but it is not damaged. The base is in primer so will need a coat of paint too. I would like $40 plus shipping for it.

This is an inlet manifold that takes either a Carter AVS or Edelbrock carburetor, it is for the B series engines typically 383 or 400 cu in. Its a bit dirty from storage on the bench but wont take much to clean it, paint it and use it. I would like $60 plus shipping for it.

Here is a B body HP manifold that appears to have the part number 2806974, it is in good condition, shows no cracks or breaks and no chunks missing. It came out of a Cbody car so it will fit. I would like $125 plus shipping for it, thanks.

Here are the manifolds you will need to suit a 70 up big block car, the drivers manifold has the heat box on it for the snorkel on the air cleaner. No cracks or breaks, clean them and fit them, I would like $250 for the pair plus shipping.

This 440 came out of a Virginia Highway Patrol car i was told, I checked and its a 77 casting block with a T code 440 stamp and HP stamp, comes as is, needs rebuild, $500 gets it.

Here is a 400 removed from the sport fury i am stripping, I think it is locked but only from sitting so long. Will need a rebuild, comes almost complete except for the valve covers and air cleaner. $300 takes it, and no free shipping :poke:

These HP manifolds will fit any 1965 to 73 C bodies. They are in good condition and show no cracks or breaks or bits missing. They are basically ready to use. The passenger manifolds bimetallic coil is dislocated and will need a little work to set it right but the shaft turns freely. I would...

This HP manifold fits pre 1970 C bodies as the 1970 on C bodies had a heater box on the upper part. But you can still use this on your later than 69 car if you wish. The passenger side is the same as B body cars. I am only selling the drivers side. It is in good condition and shows no cracks or...

I have a pair of axles here in good condition, the car was driving before being pulled apart due to rusty body. I would like $100 plus shipping for them.

I have some carburetors here for sale that are worth rebuilding, two of them the butterflies still operate cleanly and are still tight, not sloppy at all. The third carb (with the fuel filter on it, lowest one in the first pic) is frozen but could be used for parts or maybe it could be freed up...