Search results for query: *

I have a 67 300 convertible that I would like to customize a bit. Like the 68 grill look better. Is this an easy swap? Thanks

I am trying to accumulate parts needed to add power vents to my 1965 New Yorker Wagon. I have an opportunity to purchase vent motor brackets off 1965 Imperial. Any one know, or have interchange manual, saying wether imperial vent brackets will fit on New Yorker?

Hi .....I got 5 power vent window motors part number 2428282 and 2428283. Wanted to see if these are good for 1965/66 New Yorker (I am restoring a 65 NYer wagon wanna add power vents). Any advice appreciated.

Looking to install a cruise unit onto a 65 NYer wagon. I found some cruise parts listed for 1966 Chrysler. Might these be the same. I know the dash contour and layouts are same.

Hi. I would like to bench test my 65 AM/FM for my wagon. There are power red and orange wires. Also green and black which I think are speaker. Any advice appreciated.

I got some of the power windows to work for a while and now none work. Is there a power window relay? I see mentioned under drivers kick panel. I did replace the power door lock relay and those now work well. I looked under the dash and there is a fuse block......BUT no fuses at all.....what up...

Rebuilding power windows on wagon. Some of the window-regulator fastener clips broke off. Anyone can give link to replacements? Thanks and have a good day!!

Hi all. Do you have to pull out the regulator and motor all at once or can just replace the power window motor with regulator not removed? 3 out of four motors presently not working Thank you.

Hi All. Slowly addressing options on this 65 wagon. I got door panels and interior out. Working on power windows and power door locks. When I try to engage the power door locks there is a relay that clicks behind kick panel. Not sure it means short, or time for new relay.

Hi. Still working on my 1965 NYer wagon and progress is slow but positive. I have the seats out now and thinking of doing the cracks in the dash....which are not too bad. I think I read that you have to pull the windshield to get dash out. Is that true? Has anyone used this dash putty? I would...

Hi. Redoing engine compartment. Any leads on fastener?

Rear door on my 65 NYer will not open from outside or by pulling the door handle on inside. I made sure the lock was undone.. Should I yank the door panel off, cut a hole near the door handle on outside?

I have a complete cruise setup for 65 chrysler. I am going to install it into my wagon which did not come from factory with cruise. Curious if any one has done this and what problems encountered. Should I use the dash from parts car or drill out dash for cruise switch/knob

Hi All, I have a original nice running 1965 413 engine that I am going to put in my 65 NYer wagon. It is a bit dirty has 80K miles but runs smooth and quiet. Here is what I was going to do: head gaskets rear seal timing chain/gears new oil pump pan gasket timing gear cover gasket freeze out...

Hi, Any one use anything that softens door/trunk rubber seals? Mine are firm but not cracked. I am almost sure they make repro door seals, but the tail gate seals are likely not reproduced.

Found this item on eBay. I have tapes for 65 Fury and valiant. These were placed on dealer lot new cars and you would press the button and get advertisement. Tapes are real fragileLog In or Sign Up to View

Hi. I have the 65 NYer with the 413 that emitted the whitish/blue smoke when running. I took the advice of the members plus cleaned the PCV valve and fixed the carb choke and now the 413 runs very smooth without any significant smoking. Thanks for the members advice!! Here is a picture of the...

Hi, Can you clean a PCV valve on 65 Chryslers? I was thinking of soaking it in some gas or paint thinner. Do not know if that will work or just look for a replacement? Thanks.

Hi...... I bought a 65 NYer with 413 mostly for parts (no title and multiple dents). The engine runs great and smooth. It smokes quite a bit. Whitish/grey smoke. Is that a rings or valve stem issue? I intend to use if for a 65 Chrysler wagon. Thanks for advice

Hi All, I have not flooded a carb and intake before and appreciate any advice. I wired a electric fuel pump and it flooded the carb. I did not attempt to start the engine since it was a lot of fuel. Generally, should I let the carb dry out for several days? Should I check the floats on the...