Search results for query: *

Thanks, I haven’t found a broadcast sheet yet. Previous owner had the seats and dash recovered at some point. Maybe they were disposed of at that time.

The rear are 15x8 with 275/60-15 tires. The front are 15x7 with 255/60-15. The Challenger T/A you have pictured has the #2944450 15x7 black steel wheels which have the hub caps and 3" trim rings. Front and rear are the same 15x7. The T/A and Plymouth AAR Cuda had biased tires, larger G60-15 in...

This Challengers wheels are kind of what I'm going for, not sure if they were 14 or 15, but to me the proportions look just right there, especially in the front one

Thx for all the info, I learned a lot! On the red car, what's the tire size? The slightly shallower 15x7 wheel I'm assuming is in the front?

The wheels on your cool looking Polara look like the 80s Chrysler M-body (Gran Fury/Diplomat/LeBaron/Fifth Avenue) 15"x7" steel wheel (#4126675). They could also be found on some R-bodies. That wheel will accommodate up to the 3" deep Chrysler trim ring. The 2" trim ring already mentioned will...

What color is the car now? How old is the repaint?

T= 440 0= 1970 D= Belvedere Beautiful car. Does it retain a broadcast sheet? Or a build sheet? Or any other factory documentation?

Do you have a detail thread on the car? Curious about more details.

Your inbox is full

You saw the subframe is pretty rusty, right? Send me a PM. They had it out there for $3500 at one point. Depending on what they offered to you, perhaps I can buy some of the parts from it and get it down to what you wanted to pay for it? If so, I am northside of Indy, we could potentially do...

The main parts that differ are the heads and pistons. But - it seems that ~9:1 pistons for 413s are available now/again ($600), so 413s might be worth rebuilding again. With people wanting $1000+ for a needs-rebuilt motorhome 440, if someone has a 413 they should investigate using it? If one...

NOT sure about your Dodge, but the map light on our '66 Newport Town Sedan WILL light up the whole front seat, door panel to door panel. Yep, that ONE little incandescent bulb, with a clear lens and clean reflector. DO read the Dealer Order Guides at www.hamtramck-historical.com to see where...

Airport Limo ?

No I was hoping to do it with the car in the air. Guess not. Still have to clean up the transmission mount/dropout, haven't put the bars in yet. I wonder if I can effectively tighten them without the weight of the motor in the car. Probably not. The lower ball joint stud is spinning too. I'll...

nice car you have there! This is the best pic I have right now

Um, ya, I have a map light. But unless it's using a new high-powered LED it's not going to light up the whole front seat... So they only gave Fury's and VIP's these lights? Ah - wait. Looking at the '67 Monaco / Polara service manual, they make reference to (a) console courtesy lights, (b)...

Chryslers could have map lights, which could come on with the dome lamp, or not, depending upon how the map light switch was positioned. Lit up the whole front seat.

You don't tighten them until the wheels are on the ground and the torsion bars are set to the correct height. Until then they can be loose enough to allow the pin to rotate but tight enough to take up all the slack so they can't move in/out. At least that's what you're supposed to do when you...

The 1968 Plymouth service manual, Fury and VIP section, show left and right courtesy lamps, they come off the same connector that has the backup switch, tach, and gear selector light. Where (physically) are these courtesy lamps located? Did any Chrysler model (Newport, New Yorker, 300) have...

Just remember that 1969 thru April 1972 used the smaller wheel bearings, than the newer ones for 1973. The calipers are the same, but you must use the rotors for the year spindles you get.