Search results for query: *

Working on my 68 300, got my horns working again, after replacing both horns, now removed headlight motor. I cannot get the 2 screws on the body loose! I did pull end caps as far as I could, looks like inner windings are burned up. Are there after market motors out there or can these be rebuilt...

Gentlemen, working on 68 300, electric window removal. Got the 3 holes precut, ignore the 4th extra hole! Passenger side, took out the 3 bolts, motor still now coming loose. I loosened the one at the bottom left,still wont move motor. Is there something still holding motor. I have the window...

Im wondering what could my problem with my 68 300. It has been charging normal for about a year, battery is a year old, I had the alternator rebuilt about a year ago and Ihave one of those oem looking solid state regulator I got from someone here. I only drive on weekends a little, amp gauge...

I have a question about the window motor on my 68 300. I finally removed the door panel, I dont see much detail in fsm how to remove the motor, passenger side 2dr. Im not sure where to start! Can anyone give any tips on this procedure? Im afraid to start removing bolts to see what happens!!

I think this issue came up before on fuel gauges. My 68 300 had new tank, sending unit and updated voltage limiter. I unhooked sending unit and grounded it. Started car and fuel gauge went to full. Went and filled up tank and gauge only goes a little over half. I dont know if there was any...

Can some tell me what might be wrong with my head light motor, I have voltage to it but it wont open. With headlights on, I roll open manually and they open about half way then the motor starts to try and close back up. I can feel it kicking back the other way in my fingers. Any ideas what might...

Does anybody no where I can locate 2 rear side marker sockets for my 68 300. Ive been checking the usual places with no luck.

Im feeling kinda sick, 2 weeks ago I finally drove my 68 300 out of the garage and down the road and back with no issues. Felt good after 3 years! About 3 days later, before our roadtrip to new york, cranked it before we left and it ran kind of rough, slight clunking and oil light did not go...

Is there any tips on installing my new gas tank grommet in new tank? Ive heard heating it in hot water to soften up or vasoline. And then installing filler neck. Experiences on best method will be helpful! Thanks again guys.

Does anybody know where this wire connects to? On my 68 300, it was laying on floor board under driver side dash. I think it goes on steering column to ?. Can some send pic. Manual says should be grounded from column to not sure where, there is no photos. Im wondering if this missing ground may...

I just got my fuel tank delivered from summit. The original along with the bottom of my 300 were under coated. Should I apply any kind of sealer, protector or just leave bare metal? I have seen both ways. Any thoughts on this matter? I dont know if Texas heat will make any difference or not.

These are the wheels that came on my 68 300. All of the mounting holes on all 4 wheels look like this, my concern is are they wore out or do they have the wrong size lug nuts? They seem to go in to the wheel kind of deep. My other 300 had same wheels but were brand new as were lug nuts. The...

Hello all. Still getting my 68 300 ready for the road, brakes next. Can anyone recommend a good one man bleeder pump? Ive looked at a couple, real simple to bigger hand pump type. Any suggestions would be great!

One more question, going to change filter and fluid in my 68 300. Original, stock 727 transmission. Whats recommended fluid to put back in? Only a few options now days. Thanks for the help.

Does anybody have a picture of their carb set up on 68 440 or tips as to what goes where? Carter came with this 300, was in a box, junk. Put on this one, bought the linkage adpt but Im not sure where to hook things up. I dont remember how to set up the trans kick down lever. Also the pic of heat...

Quick question guys, not sure what size vacuum hose for dist advance, and there are to ports on front of my carb. Left and right, kind of hard to see left one. 2 different sizes. Which one is recommended for dist advance?

Well I received my solid state regulator for my 68 300 the other day. Installed it today and gave test run, voltage ran up to 14.9 and went no higher. Let it run about 25 mins. I am happy with that. Oil pressure at start up, 70 lbs, idles 28-30. Going to put sending unit back in now. Sending out...

Can anyone tell me a good maker or a good place to get transmission filter and gasket for my 68 300? I need to go ahead and change these out while ive got the car up on jack stands. Another new project for me. Doesnt look to be to difficult. Any quick tips?

Just picked up my air breather from the shop. Sand blasted and powder coated. Fixen to put it my 68 300. Dont know if I am gonna put labels on, or let it shine! I did inside and both sides of base to. Guy did a good job I think.

Still having an issue with my 68 300 charging system. Rebuilt alt and new mechanical voltage reg. Grounds are good, took voltage reading at battery. Start up 12.5, continues to slowly rise after a few minutes to 16 volts, reg starts to smoke and I shut down the engine. I am not sure what to look...