Search results for query: *

Couple of questions: Dome Light on ceiling…yellow and pink wires go up through a-pillar to dome light…both have 12 volts on them. 12 volts on yellow wire flows through light bulb to ground (with switch on dome light forward) when either door gets opened. When doors are shut, 12v. gets...

Going down the road steady-state…45…55 mph can feel engine is not smooth…it “bucks,” it’s a 62 318 poly…my 350 in my 58 DeSoto did this and I put in new condenser…fixed it. Tried it on this 318…didn’t work. Have also changed points and coil too. Still does it. Engine is not a smooth idler...

Have been trying for a long time now to fix the leaks in my transmission. It’s a 1964 727…in a 58 Plymouth. Replaced kickdown shaft seal already now the push button shift cable is leaking at the adjustment dial. Cable itself looks fine but there must be a seal between that adjustment dial and...

Why does my 68 Fury 383 dump gas after shutting down? The smell is obvious and it’s done it ever since I owned it which is eight years now. I have an aftermarket 4 barrel carb. on it now for…. started out with the stock Carter two barrel, dumped gas with original and it’s still dumping gas...

Just wondering if anyone here has used plastic dip spray on any painted surfaces of their car? In my case, I want to blacken the inner areas (5 on each wheel) of my silver powder coated rally wheels. I’m dreading sanding all those little areas. I’ve heard: If you clean it real well, tape it off...

Was rummaging around in local junkyard for some parts for my 69 Polara when I stumbled upon this ~ 70 Fury Wagon with a decent black dash pad. Was not able to open Driver door…passenger door opens and windshield is mostly gone now and there’s an old AMC Javelin on top. What do you think guys...

Has anyone ever figured out how to use them on the rally steel wheel WITHOUT having them dig in to/damage the freshly painted rim. In my case, I paid the extra to get them powder coated and now I hate to rubber hammer them on. LOL Other than cutting off all teeth on backside/using some sort of...

https://www.ebay.com/itm/260750640612?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=7cDziYpFRLq&sssrc=2349624&ssuid=jJvhE6rHTA2&var=&widget_ver=artemis&media=COPY Are these the correct lug nuts for 60’s mopars? I have all original wheel studs on my cars. Want to put 14” Rally wheels on my 68...

Just started removing plastic covers and things last night. Dash pad needs to be removed…someone did it before did a terrible job fixing dash pad and unfortunately wound up breaking lots of the plastic dash pieces around speedo and under steering wheel. I’m going to try and straighten all this...

69 Dodge Polara…318 automatic originally A/C car. Bought it 3 years ago always thought PASSENGER side fresh air vent behind kick panel was broken. Driver side works fine. Took apart yesterday to find passenger side air vent has no vent…just a factory cover over it…but lever under dash and cable...

Hi Everyone, Just thought I’d post this to get some feedback/opinions. I have a 69 Dodge Polara 2 door hardtop with a 318, auto. trans. Ran rough when I bought it in 2020. Couldn’t straighten it out with tune up so did compression check. Sure enough #2 piston had very low compression and a few...

My chrome mirror surround is mint except up/down adjustment flips around due to control wire broken at mirror end. I do believe mirror could be changed out but I’ve never done it. If so, perhaps some guidance would help me along with a good replacement mirror/remote adjustment mechanism. If...

Looking all over for decent floor mats that’ll fit well in my blue 69 Polara. Fronts have to be at least 30” long by 22” wide. Rears not as important but should be about 16” x 20”. Would like carpet or at least a carpet/rubber mix. The universal mats out there are only like 27” x 17”. What are...

Trying to figure out which way is open. Has original crossover pipe with single exhaust pipe. I have a feeling it’s not working properly like most. Want to wire it open but don’t want to remove crossover pipe to see inside. Anyone have a definite answer for me? Thanks.

I’d sure appreciate some suggestions on best electronic ignition kit for my 68 Fury III 383. Best place to buy from too please…I remember years ago putting a Pertronix on my 69 Fury III 318. Don’t remember where I got it. Worked great but I also remember getting a new flamethrower coil with it...

My 1968 Fury III is an absolutely mint survivor car. When I bought it in 2016, I noticed remote mirror lever on driver door was bent downward. Figured that was not right but mirror worked fine so I left it alone. 7 years later…took it out first drive of the new year/last week and I noticed...

Have to replace upper right balljoint in 58 Plymouth. Inner tire treads were wearing out. Have friend helping me got upper balljoint and a-arm freed up today. Still have to unscrew it tbough to remove it. Need socket. Where can I get and what size is it? I found ball joints…they seem to be...

Getting my 318 back together here…From what I remember, I had no exhaust leaks prior to disassembly…and found NO gaskets in there. What do you think guys? Should I install exhaust manifold gaskets or not? I do have a set that I remember putting on the 318 in my old 70 Fury back in the day...

Has anyone ever used high heat paint on exhaust manifolds? I’m getting my 318 back together…last thing to go on are the exhaust manifolds. Wondering if I should wire brush them and put some high heat paint on them. Can reads good to 1200 degrees. ? Anyone ever tried this or is powder coating the...

This fan (top 2 photos) came off my 69 Dodge Polara with 318. As I bought it, it had a lot of aftermarket parts under the hood…chrome valve covers, round chrome air cleaner, stainless braids on all the hoses etc etc. I have a good suspicion this fan is aftermarket too. Can you guys confirm? I...