Search results for query: *

Request the benefit of your expertise. Friend of mine has a low mileage 1977 Chrysler NY 9.25" rear. As far as installing it on 1972-1973 Dodge/Plymouth c-body, is it the same width as a 1972-1973 rear? same spring perches? Other fitment issues? Thanks Currently, my only c-body is 1970 Fury...

I have HP Exhaust Manifolds and I'm trying to switch to stock 1970 Valve Covers. I used Chrysler Race Hemi Orange to paint the valve covers. I did not use primer. Clearance on the right side from HP exhaust manifold 2806900 to the valve cover is tight. After 30 miles of driving, I had burnt...

Oil Cap from 1970s Big Block Valve Covers. Ditching the cheap chrome junk valve covers and going back to stock. Oil cap Rubber Seal was rock hard. 1st pic on right. Where can I buy a new Rubber Seal? just FYI. VHT SP 100 sprays on normal. Duplicolor DE 1652 is runny. I had to use 7 very light...

Clogged Vapor Separator, 4 vent gas tank. Clogged at output port. Output port visible in second pic. Vent ports are not clogged. Tried rust penetrant. Tried wires and brushes. No help. What do you do to unclog a vapor separator? Soak it in carb cleaner? Can I break that odd looking weld apart...

Anyone have a source and part number for a new vented gas cap for 1971 Fury? Tried Van's which has an A-body vented cap, but not sure if that will work FSM calls for vented. Thanks

I was trying to match up a correct fuel tank filler neck for my 1971 Fury. I got a filler neck from a 1973 Dodge. I think they are a match but the 71 Fury mounting bracket may be taller, so 73 filler neck does not bolt in. Anyone have a Hollander manual to see if 1971 Fury and 1973 Dodge...

I want to thank everyone who tried to help me with my 1990 W150 pickup. Over the last 3 years, the TBI truck had developed many wiring problems as a well as other electrical malfunctions. I considered trying to fabricate a wiring harness that would take the computer out of the picture and render...

My question is on durability of 1992-2003 Magnum Heads In an article on building magnum V8 engines, Mopar Action, Feb 2014, Rick Ehrenberg tech editor says: “Most, if not all, of the magnum V8 Heads castings, with anything over 50-75K miles, will have cracks in the exhaust seat. True, the...

I have a 1990 W150 Power Ram 5.9/46RH. It has TBI with a return fuel line. It has SBEC as its computer. It has a Hall effect distributor with a 5 V return wire to the computer that allows the computer to calculate RPM and helps the computer to then calculate the amount of fuel to send through...

My 90 Dodge W150 truck has a 1992 LA block 5.9 L V-8 out of the B350 Dodge van. The engine has about 86000 miles, never rebuilt. The engine developed a leak along the right side of the timing chain cover, so anti-freeze was dripping on the concrete floor of my carport. Some observations about...

Our situation with my wife's 2011 Dodge Nitro 114,000 miles is that it is been running poorly and sometimes refusing to start. Check engine light on. Engine codes are cylinder 3 misfire permanent and multiple cylinder misfire permanent. Removed left side valve cover. I was hoping to see a rocker...

I have a 1973 Dodge with original 360 V-8 engine. The car starts and drives okay. However the base of the distributor does not seat against the top of the block. There is about 1/8 inch of clearance between the top of the block & bottom of the distributor base. Further the distributor is very...

I have a question for the axle experts. Will a formal 1974 – 1978 rear axle fit on later fuselage cars? In other words, did Chrysler change dimensions spring center to spring center and drum to drum when the formals were introduced? Or are the formal rear axles interchangeable with the 1972...

https://www.amazon.com/gp/product/B07PN9FJKJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1&pldnSite=1 On @Big_John 's recommendation, I purchased this tool to see if my car still had original nylon tooth cam gear. Camera on end of cable sends images through wifi in control box. Works with...

I was looking for a small 4 barrel carburetor for mounting on a 1971 small block spread bore intake, 351-2100. I came across the Holley 1900/1901. The 1st thing that leaps out at me, as the article says, is that it is a 3 barrel carburetor not a 4 barrel carburetor...

I purchased the intake below from C-Body Bob. 1971 Model Year 3512100. (Yes, it will go to a machine shop for clean up. No, I do not care that it weighs 47 lbs. My car is heavy anyway and I have no intention of racing it.) I would like to use the choke heater block off and an electric choke...

If I have a kickdown linkage from 1973 360 V8 with Holley 2210 2 bbl, which seems a fairly wide carb, will that kickdown linkage also work on a 4bbl if I use a spread bore factory intake and a thermoquad? Thanks, Ben (no parts for sale)

I bought VHT 126 Early Chrysler Blue Engine Paint. Did Chrysler change the color of Chrysler Engine Blue in the 1960s and take out a green tint? VHT 126 VHT sprayed on hinge My Valve Cover 1970 & later

I have a 1971 727 BB trans. I can read all the left side oil rail numbers. I think the VIN last 8 digits is supposed to be right side near the oil fill tube. Does anyone have a picture for where it is located. Having trouble finding it. Should be same for 1969 thru 1971 maybe later too...

I purchased these with a fiberglass stiffening rib for $45 + ship from Tennessee Real Gaskets on ebay. In 36 years of seriously working on cars, I've never received folded valve cover gaskets. I initiated return. Does this piss anybody off besides me? Or am I overreacting?