Search results for query: *

Bill's Turquoise looks too dark to my eyes, but the late 50s Pontiac Turquoise he sell's looks real close to Chryslers original.

See post #10

Some people are using Bill Hirsch’s late 50s Pontiac Turquoise and finding it to match existing overspray on bellhousings, torque converters and what not. It’s what I’ll use if I ever give the engine a “Craigslist rebuild.”

I heard/read it was influenced by the Mercedes Pagoda top from ‘63

I'm running a OEM unit from HalifaxHops now, and my blue box from Rick is in the trunk as an emergency use only "spare."

So I did a check on my choke pull-off and it failed the test procedure (it would not hold vacuum for 10 seconds). Interesting, since it was working fine 2 years ago when I rebuilt the carb. I was surprised it worked as well as it did then, so I guess I got lucky. I've ordered a replacement from...

I checked that yesterday with my vacuum pump and it was working. I’ll try to observe its function while the car is running. Thanks. EDIT - it was moving under vacuum applied, but not HOLDING vacuum. So, it was indeed not working correctly.

So, after my distributor grenaded and caused all manner of bucking and stumbling, my choke settings are no longer what they used to be. My fast idle speed has changed and the choke plate seems to be closed too much, causing it to run like poo-poo on initial start. I’ve made some adjustments to...

my ‘08 Uplander has been one of the most reliable cars I’ve ever owned. The 3.9l pushrod V6 is bulletproof. I’ve changed out axle hubs, CV axles, a fuel pump, several sets of tires, rotors and pads 3 or 4 times, sliding door bearings, spark plugs and wires, door lock actuators, yet because I’ve...

As an aside, I was changing out the front hub/bearing assemblys on my mid-aughts GM FWD minivan, and I asked a "professional" mechanic friend of mine if I should do things like replace the lower ball joints, tie rod ends, etc., while I had it all apart. He replied, if those OEM parts are still...

I could give some questionable advice but I’ll refrain to avoid the red X. Following, since I have the same issue.

I am also running ethanol free. Thanks for your insights. I'm going to a couple of tanks of gas with no 2 cycle oil at all and see if it's a carb issue first. If nothing, I'll go back to adding it in and watch the color. Thank you!

I was told it was to replace lead as an upper-end lubricant

So upon the advice of some here at FCBO, I've been using 2-cycle marine oil as an additive to my gas at 1oz:5 gal of 91 non-ethanol gasoline. While dealing with my distributor malfunction and troubleshooting the entire ignition system, I found my spark plugs were quite brown and glazed (making...

AND THE PROBLEM WAS . . . #3 spark plug side electrode got bumped upon installation and had zero gap. It probably, kinda, sorta, worked above 1500 rpm, but at idle I don't think it was firing. It was basically black, while the other plugs around it had started to take on the tan color. I...

I've never heard of using a shop vac in this manner. Where does one put the shop vac tube, and where does one listen from/to? Thanks!

Great advice everyone. Thank you. I'm gonna pull plugs 1,3 & 5 just to compare. These are brand new plugs that have only ONE run cycle on them (yesterday). Then I'll use the borescope to take a peak inside the cylinders. After that I'll get her warmed up and use a vacuum gauge to see what...

Got my distributor replaced with one from HalifaxHops after the "Rick E." unit I had self destructed. The engine fired right up, but there still seems to be an issue. I haven't driven it yet, but just getting it warmed up I can tell it's running rough. I put new plugs in it while the dizzy...

Yes. I checked FSM, and .006" is correct. I measured with feelers and I came up with .016" of side play. Trash, in other words. I don't think I want to rebuild this distributor, as who knows what else might be lurking below . . . I'll check with @halifaxhops and see what he can do for a...

I’ll check the specs in the FSM but this is the Rick E distributor I bought two years ago. It only has about 2000 miles on it.