Search results for query: *

that Motive Gear C clip is not used in an 8 3/4 rear...in an 8 3/4 the bearing is pressed onto the axle shaft...those clips are used in the rears where you pull the rear end cover ,remove a pin and the clip goes into a groove cut around the end of the axle to hold the axle into the side gear of...

I looked up my Dr Diff receipt and it only showed the carrier bearings and the clutch kit, so I guess I sourced the Timkin ones I used someplace else...but my notes say they were USA made...maybe they were on a separate receipt, cause thought I got it all from him...the set7 bearing comes with...

those cutouts allow airflow around the port that feeds exhaust under the intake manifold to pre heat it

IF you have a/c, there are 2 rubber hoses that connect the heater core to the ''h" pipe inside the heater box...these may be leaking and not the core itself but the whole box needs to come out to fix them...there is vent housing at the bottom of the box that 2 air distribution hoses come off...

looking at TCP Global's auto paint library for a 65 Chrysler I wonder if they repainted it 66-1 mauve poly? I think the area of the door inside the rubber weatherstrip is the original color...different interior colors were usually on bolt on parts like the dash...I don't think they would bother...

I used HF's Pittsburg branded one...it was half the price of the MiteyVac. worked fine for the actuators...for the whole system I did what the FSM recommended...made a setup with a gauge and a bleed valve, hooked it to my A/C vacuum pump...the bleed valve let me limit the vacuum to 8 lbs ...had...

believe that's FURYGT

my local PPG dealer had formulas for my DD1 mist blue (68)...most body shop supply stores only carry one or 2 lines of paint so you may have to shop around...my Axalta dealer didn't have a formula for it but sometimes its a case of "somebody tore that page out of the old book"...there are places...

that time frame sounds a lot less horrible than what I've read about on other threads...

its a 9 1/2...its kinda an apples and oranges deal....original budd style discs on slabsides used 4 piston calipers, a larger diameter master (1 1/8) for the extra volume and a dual diaphragm for the extra force to push it....the 71/73 single piston calipers used a smaller diameter master (1...

not to overly complicate your search but I've been running a single diaphram Midland (drum) booster with discs for over 20 years

The back plate and pedal assembly are different...here you can see the 4 holes where the booster bolts on

the screws under the windshield gasket cannot be accessed with the windshield still in the car...they would only need to be removed if you wanted to remove the entire metal dashboard ...you don't need to do that if all you are replacing is the dash pad...I don't know if access is better or worse...

depending what you are putting them on the ones that come with lugs will probably all be right hand thread ....I think there are "correct style" lugs out there with a dimple on the top (PG performance?) if you care about that....Ford center caps probably have a different decal so check what they...

Stephens Performance has a Mopar salvage yard in Alabama...you may be able to source what you need there

idk if its available in your area but I like Permatex Ultra Copper silicone on manifold to head...very thin coat, don't let it dry, assemble wet...let it thoroughly set up like 24 hrs before starting...it will fill any minor imperfections and if it has nothing to fill it will just squeeze...

triangular tag on carb...6134s on top line, 3425 in lower, and a large 32 (twice the size of the other numbers) in the drivers side lower corner...car had some sort of green and white decal on middle of passenger fenderwell, there's only a 1/4 inch piece of it left...I assume it was the typical...

Here's the carb on my 68 fury wagon...idle screws face forward under float bowl...nothing was capped off...I'm the one who rebuilt it, swear it was original...when you said idles were plugged I assumed it was much newer

unfortunately the gasoline we buy today is not the gasoline that was available 50 years ago...in my experience it burns leaner, especially if it contains ethanol...and if it has a "non adjustable" carb that generally means it's from a year where they were trying to minimize emissions so it was...

your color looks a lot like Ford portofino blue...think it's a 94 color... a light metallic blue with a purple tint...I have a Chevy C10 I painted that color