'68 300 Stock Rims, wider tires

[mgm1986]

Howdy all, hope you're having a great month!

I am planning to replace the tires on my '68 300, currently running 225/75R15 at all four corners on stock rims (maybe not stock at 15" but they have the Chrysler cover I want to keep).

I would like to keep the same rims and go with wider tires like a 235/75R15. Does anyone know if this will work with these rims? If so, any issues with rubbing without making any other changes?

Thanks!

 

[Dads300]

Should be zero issue. I run 235/75/15 on the front of my 66 300 with plenty of clearance. The tire will also be fine on any stock rim, be it 6”, 6.5”, or 7” wide.
Travis..

 

[413]

Yes just fine, many have used that size tire on stock wheels.

 

[mgm1986]

Awesome. I like the look of a wider tire but I also like the rims I have. I was concerned the rear wheels might rub against the fender skirts. Thank you both for your expertise!

 

[CBODY67]

I put P245/70R-14 BFG Advantage TAs (from back in the middle 1980s) on '65 Chrysler wagon 14x6.5" wheels on my '67 Newport. No issues anywhere! Other than I had to jack the rear end up by the center of the rear axle and put the jack stands just in front of the rear wheels, in the "jacking location" there. The tires could be jostled and angled enough to get them past the quarter panel and brake drum (11x2.5" drums), but it just took a bit to get it done. 11x3 rear drums might require the lower shock mounts to be undone, though, to let the axle drop down a bit more, it seems.

Enjoy!
CBODY67

 

[Big_John]

I am planning to replace the tires on my '68 300, currently running 225/75R15 at all four corners on stock rims (maybe not stock at 15" but they have the Chrysler cover I want to keep).

I would like to keep the same rims and go with wider tires like a 235/75R15. Does anyone know if this will work with these rims? If so, any issues with rubbing without making any other changes?

That's only about 3/8" wider.

 

[carguy300]

235/70's would look and still fit good.

 

[mgm1986]

235/70's would look and still fit good.

This is probably the route I will go to keep the ride height close to what it is now.

 

[Big_John]

This is probably the route I will go to keep the ride height close to what it is now.

You might want to punch in your numbers here: Discount Tire | Tires and Wheels for Sale | Online & In-Person

To make any real width changes, you need to go to a larger size. Of course, you are limited by what's available. That 235/70-15 is still only 3/8" wider, but now it's 5/16" smaller in diameter.

 

[straightjob]

Howdy all, hope you're having a great month!

I am planning to replace the tires on my '68 300, currently running 225/75R15 at all four corners on stock rims (maybe not stock at 15" but they have the Chrysler cover I want to keep).

I would like to keep the same rims and go with wider tires like a 235/75R15. Does anyone know if this will work with these rims? If so, any issues with rubbing without making any other changes?

Thanks!

I have the same size on my bronze 68 no problem!

 

[mgm1986]

@straightjob Thanks for confirming! I have put a little over a thousand miles on the old girl since bringing her home from your place in October and she loves to drive!

 

[chippers65300]

I'm running 245-60-15 on Magnum 500's all 4 corners on my '65 300L. Same skirts as your '66 300. Zero issues but jacking the body up higher with the rear axle on jack stands to remove them.