Budd Caliper's

[doooodaaaah]

Does any body have a lead on replacement budd caliper's or rebuild kit or even an aftermarket caliper that can be made to fit?
Ive Got one that's leaking
Im in the UK which makes it more difficult
Thanks
In advance

 

[67Monaco]

Went through 3 different Cardone reman'd calipers before I gave up. I ended up with Wilwood calipers. Made my own caliper adapter bracket. The factory spacing between caliper bolts is 6 and 7/8 inch. The Wilwood bolt spacing is 3 and a half inch. How you shape the adapter bracket would be based off the rotors used. Since I also didn't use factory rotors, my other measurements wouldn't mean much to you.

 

[doooodaaaah]

Went through 3 different Cardone reman'd calipers before I gave up. I ended up with Wilwood calipers. Made my own caliper adapter bracket. The factory spacing between caliper bolts is 6 and 7/8 inch. The Wilwood bolt spacing is 3 and a half inch. How you shape the adapter bracket would be based off the rotors used. Since I also didn't use factory rotors, my other measurements wouldn't mean much to you.

it had crossed my mind to do this but i thought refurbing or replacing the calipers would be eaiser, but being my first mopar i didn't realise the brakes were that rare or hard to get parts for.
Can I ask which wildwood calipers and what rotors you used? also you have any photos just to give me more of an idea
Thanks

 

[stain]

Mine leaked while sitting. they where "rebuilt"
I just disassembled them, cleaned everything and reassembled. It does not leak anymore.
I was surprised by how thin the piston bore seal was. Much thinner than smaller calipers I have rebuilt. If any debris gets in there, I can see where it would cause a leak.

 

[doooodaaaah]

Mine leaked while sitting. they where "rebuilt"
I just disassembled them, cleaned everything and reassembled. It does not leak anymore.
I was surprised by how thin the piston bore seal was. Much thinner than smaller calipers I have rebuilt. If any debris gets in there, I can see where it would cause a leak.

I’ve just started taking mine apart I have to kinds of piston in one caliper I suspect it’s incorrect

 

[67Monaco]

it had crossed my mind to do this but i thought refurbing or replacing the calipers would be eaiser, but being my first mopar i didn't realise the brakes were that rare or hard to get parts for.
Can I ask which wildwood calipers and what rotors you used? also you have any photos just to give me more of an idea
Thanks

wilwood 120-15254. I used 2014 Lincoln MKZ rotors. It did however require threading the spindle so I could run the bottom bolts in from the opposite side to clear the rotor. It's VERY tight, and no way to get the factory dust shields on. I don't think I would do it again. BUT they were the closest to the factory rotors I could find. The hub could be machined as was done by others for the Mazda rotors to make clearance for the rotors, but I didn't have a lathe or rotary table at the time.

 

[doooodaaaah]

wilwood 120-15254. I used 2014 Lincoln MKZ rotors. It did however require threading the spindle so I could run the bottom bolts in from the opposite side to clear the rotor. It's VERY tight, and no way to get the factory dust shields on. I don't think I would do it again. BUT they were the closest to the factory rotors I could find. The hub could be machined as was done by others for the Mazda rotors to make clearance for the rotors, but I didn't have a lathe or rotary table at the time.

just looked on rock auto says the the lincoln's bolt circles 4.25 not 4.5 am i missing something?

 

[67Monaco]

just looked on rock auto says the the lincoln's bolt circles 4.25 not 4.5 am i missing something?

Sorry, 2011.

More Information for FVP 6620629

This is where I made them fit with budd calipers. Then I gave up and went Wilwood. Had i done that in the first place things would have worked out different.

The Sheriff

You left out the part where they find a way to make it so every single one of them has some sort of flaw built in. Nobody said anything about paying extra for QC/QA... Trust me. The plant won't be ISO 900x Certified.

www.forcbodiesonly.com

and where the wilwoods come in to the picture.

The Sheriff

Yeah factory disc car. took the originals apart in hopes of potentially rebuilding them. One piston in each side are frozen. Attempted to plug the holes and use air pressure to push them out. Ran the pressure up to 80PSI before I ran out of cajones. I didn't need a missile shooting across...

www.forcbodiesonly.com

 

[stain]

SO, CARID lists calipers for the 1968 Chrysler. They are from R1 concepts. They are not listed on R1 concepts page. I called in august to see what the deal was and got no help. They are $200 a piece if you want to take a chance. they claim " guaranteed to fit" so they should take them back if not the case.
https://www.carid.com/1968-chrysler-new-yorker-brake-calipers/

 

[67Monaco]

SO, CARID lists calipers for the 1968 Chrysler. They are from R1 concepts. They are not listed on R1 concepts page. I called in august to see what the deal was and got no help. They are $200 a piece if you want to take a chance. they claim " guaranteed to fit" so they should take them back if not the case.
https://www.carid.com/1968-chrysler-new-yorker-brake-calipers/

If they work that's the route I'd go.