Wollfen
Old Man with a Hat
I will look through the rest I have and get back to you on the wiper blades. I think the type you show have a release tang on top near the pivot. Will get back to you tomorrow.
For Sale 1969 Chrysler 300 convertible for parts
- Thread starter Wollfen
- Start date
Wollfen
Old Man with a Hat
Okay, I found five of your type in my stockpile, but only two that I consider to be in good condition, the two pictured are still good with only a little bit of side play in them. They are not loose and sloppy like worn ones can get. I would like $10ea for them and i will throw the washer bottle in for free as I am not sure it will survive the trip without damage.
Sold, thanks for going the extra mile for the wiper blade assemblies. By my calculations the total is 55.00 plus the ride. Can fire a check off first thing tomorrow if that's OK. PM me the total price and ship info Thanks for your help.
Wollfen
Old Man with a Hat
Will PM you a shipping cost to your zip code too once i have calculated it.
Zip is 46226
Wollfen
Old Man with a Hat
@C Sickness here is a pic of the letters, there is one E missing, three of the letters only have one stud, the rest are intact. Some of the letters show some slight pickling around the back edge. Other than that they are in good condition.
bluefury361
Old Man with a Hat
Right side tail light lens......? to 36535
thanks
Will.
thanks
Will.
GBsPanhead
Active Member
How about the window "whiskers"...the felt peices?
Did you sell the brake booster and MC? Thanks!!
Did you sell the brake booster and MC? Thanks!!
Wollfen
Old Man with a Hat
Will, the tail light assemblies are in very good condition and I would like to sell each one as a unit rather than pull them apart. One side would be $55, let me get a pic of the assy for you.
Wollfen
Old Man with a Hat
MM, not sure what part is the felt pieces? Can you supply a pic of yours? As for the booster, it is gone, I sold the disk brake system out of the car.
GBsPanhead
Active Member
It's the felt that goes against the windows. Need for all 4 windows, (front/back). You can see the slots that it attaches to. I'm missing these pieces. Trying to complete. Thanks!
Wollfen
Old Man with a Hat
Ah I see, the window felts yes, I beleive you can buy these new , check this link for an example.
Window Felts 69-70 Fury Convertible w/Vent Window
GBsPanhead
Active Member
I had seen these before. List as fitting '69 Fury 'vert, I have a '69 300 'vert. Are you saying these would fit? I could of sworn I contacted this company before, and they either were not sure/clear. I can't remember now. Let me know. Thanks!
opps… just re-read your post...you stated as an example.
Wollfen
Old Man with a Hat
I can check with the cars I have here, I am pretty sure they would be the same. Best to start a thread putting the question out there though.
GBsPanhead
Active Member
Thanks! Sorry to get off-track. I sent them an e-mail.
Derek Myers
New Member
Your inbox is full. I need interior screws. All the screws for the trim on the inside of the windshield and all of the screws that hold the plastic trim on the bucket seats. myersd@wowway.com
bluefury361
Old Man with a Hat
thanks Gary. All I need is a lense to complete my set. I'm looking to make a lighted wall hanger.
Wollfen
Old Man with a Hat
I haven't forgotten you, I will get stuck into it this week., it was raining all week last week. One question, do you want the whole drip rail intact from the back edge of the doors?
Samplingman
Old Man with a Hat
Cool, no rush. I’m not sure what you mean, the drip rail doesn’t extend to the doors, does it?
Wollfen
Old Man with a Hat
I will rake pics for reference of what I mean.
Similar threads
